RCP-100Guide to Installation and OperationM191-9900-110 Remote Control Panel Copyright 2009 Miranda Techn
GUIDE TO INSTALLATION AND OPERATION 6 | RCP-100 Case 2 (figure 3.5) In this case, multiple RCP-100s are connected on the LAN. Only one of these
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 7 Case 3 (figure 3.6) Here an iControl APPLICATION SERVER is connected to the LAN. In this case, al
GUIDE TO INSTALLATION AND OPERATION 8 | RCP-100 4 Operation 4.1 Powering Up The RCP-100 has no power switch. Plug the unit into an appropriate AC
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 9 Device Activating this pushbutton (LED is GREEN) enables the device selection mode. Use the rotary
GUIDE TO INSTALLATION AND OPERATION 10 | RCP-100 Group list: This is the default list mode. All devices are listed in terms of group and device nam
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 11 When the selected device (or the frame that holds the device) is not accessible, an error message
GUIDE TO INSTALLATION AND OPERATION 12 | RCP-100 4.3.2 Device Locking The protection provided by this feature is only meant as a safety measure to p
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 13 Each of the 4 encoder knobs increments/decrements the associated field in the IP address. Pressing
GUIDE TO INSTALLATION AND OPERATION 14 | RCP-100 1. DCOM is ON, (and follows the IP address if it is changed) 2. DCOM is changed from OFF to ON an
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 15 4.4.1 Parameter Page Keys The five FUNCTION keys are assigned the role of PARAMETER PAGE keys in
GUIDE TO INSTALLATION AND OPERATION RCP-100 Safety Compliance Information Safety Compliance This equipment complies with: - CAN/CSA C22.2 No. 6095
GUIDE TO INSTALLATION AND OPERATION 16 | RCP-100 To navigate backward up the menu, press the "user" button; you will back up one level for
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 17 4.4.4 Requirement to Restart the RCP-100 There are a number of circumstances when it is importan
GUIDE TO INSTALLATION AND OPERATION 18 | RCP-100 5 Upgrading the Operating Software Two methods exist for upgrading the RCP-100’s operating softw
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 19 1. Insert the compact flash on RCP-100 panel (left). Wait for 2-3 seconds to allow RCP-100 to de
GUIDE TO INSTALLATION AND OPERATION 20 | RCP-100 RCP100.xxx> makeupdatedisk RAM disk initialized - size is 5000 blocks... Volume name is 3.0.0 Cu
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 21 RCP100.xxx> copytoflash Erasing and copying may take several minutes. Moving data to flash disk
GUIDE TO INSTALLATION AND OPERATION RCP-100 Table of Contents 1 RCP-100 Remote Control Panel ...
GUIDE TO INSTALLATION AND OPERATION RCP-100
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 1 1 RCP-100 Remote Control Panel 1.1 Introduction The RCP-100 is a simple, 1RU remote control pan
GUIDE TO INSTALLATION AND OPERATION 2 | RCP-100 2 Overview 2.1 Front Panel The RCP-100 front panel consists of the following: - the function
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 3 3 Installation 3.1 Unpacking Make sure the following items have been shipped with your RCP-100.
GUIDE TO INSTALLATION AND OPERATION 4 | RCP-100 Ethernet Use this RJ-45 female connector to connect the RCP-100 to a Local Area Network (LAN) using
GUIDE TO INSTALLATION AND OPERATION RCP-100 | 5 CLIENT runs only the Client module, and is connected through a LAN to an APPSERVER which is basica
Kommentare zu diesen Handbüchern